QSC BASIS 914lz Instrukcja Obsługi

TD-000200-00 rev.BBASIS 914lz4X16 CobraNet Enabled Control and Monitoring Signal ProcessorHardware Manual*TD-000200-00*

10Example #5 - Two-Wire Interface (separate network hardware):Example #5 is conceptually similar to example #4. The difference here is that separate n

11UnpackingThere are no special unpacking precautions. However, it is recommended you keep the original packing material for reuse in the rare event t

12Computer Requirements & Software InstallationInstalling QSControl.net is easy. All you need to do is choose the folder where the program is to b

13General Information & Configuration MemoriesAmplifier SetupThe QSC DataPort-equipped amplifiers connected to the BASIS 914lz must have their pow

14ConnectionsAC Power CordInsert the molded receptacle of the AC power cord into the AC power inlet on the back of the BASIS 914lz. Plug the AC line c

15RS-232The RS-232 is an optional utility serial port for accessing advanced features. Connect to an available COM port on your PC and communicate usi

16LED Indicators (continued)QSControl and CobraNet Network Status (Port) Indicators- There are two groups of three LEDs on the front and rear panels l

17LCD Navigation Map Left side buttons have screen dependent functions.This read-only screen is the “out of the box” default display after power up. T

18Getting StartedThis section outlines one of the simpler methods of getting familiar with your BASIS and the QSControl.net software. The goal of this

19Getting Started (continued)17- Select Device, Add Device, from the menu. A new window will open prompting you to name the device. Name it logically,

2IMPORTANT SAFETY PRECAUTIONS & EXPLANATION OF SYMBOLSThe lightning flash with arrowhead symbol within an equilateral triangle is intended to aler

20Operation QSControl PortThe QSControl port operates on a 10BaseT Ethernet network. This port is one of the primary means for connecting QSControl.ne

21Utility/Diagnostic FunctionsSafe Mode SwitchLocation of Safe Mode switch: The front panel has a small access hole on the left side, just left of the

22Utility/Diagnostic Functions (continued)RS-232 Communications Procedure:1) Connect the RS-232 port of the BASIS 914lz to an unused serial port (COM

23Utility/Diagnostic Functions (continued)Telnet AccessThe RS-232 features can also be accessed via Telnet. The Microsoft Telnet application is a Wind

24Preliminary SpecificationIN OUT THRUDynamic Range (AES-17, -60dB Method, all sensitivities)unweighted >112dB >112dB >110dBA weighted >11

25Preliminary SpecificationOmni Inputs 2 discrete inputs for TTL logic, voltage control or passive resistiveConnector Type 2-pin "Phoenix Style&q

26Dimensions

QSC Audio Products, Inc. 1675 MacArthur Boulevard Costa Mesa, California 92626 USA©2005, 2006 “QSC” and the QSC logo are registered with the U

3Introduction1- Power indicator2- Diagnostic indicator3- Network status indicators4- Port connection status indicators5- Multi-function push buttons6-

40.396 milliseconds. When analog input and analog outputs are used, the total delay is 2.354 milliseconds. The delay does not change regardless of the

5Introduction - Networking the BASIS 914lzThe BASIS 914lz has two RJ-45 network connection ports on the rear panel. One port is labeled "QSContro

6Third, the BASIS 914lz and QSControl.net system are targeted at network switch deployments. The consumer costs of Ethernet switches have continued to

7Example #2 - CobraNet X-over mode:This is the simplest connection you can make between two BASIS boxes. Use a CAT-5 crossover cable connected between

8Example #3 - Single Wire Interface:Here all QSControl.net and CobraNet traffic shares the same single CAT-5 cable between the BASIS 914lz and an unma

9Example #4 - Two-Wire Interface (shared network hardware):This example illustrates the Two-Wire Interface with a managed Ethernet switch. The switch